DOWNLOAD Test Reports
DDRC SRL Healthcare Packages

DDRC SRL Clinical Test

Under Your Tests...Empower Your Health

Activated-clotting-time



Why Get Tested

To monitor treatment with heparin or other blood-thinning medications anticoagulants when undergoing heart bypass surgery coronary angioplasty or dialysis

When To Get Tested

When you are receiving high doses of heparin to prevent clotting during surgical procedures such as a heart bypass when heparin levels are too high to allow monitoring with a PTT and or when a rapid result is necessary to monitor treatment

Sample Required

A blood sample drawn from a vein in your arm

Test Preparation Needed

None




Common Questions


The activated clotting time ACT is commonly used to monitor treatment with high-dose heparin before during and shortly after medical procedures that require that blood be prevented from clotting such as heart bypass surgery cardiac angioplasty and dialysis High doses of heparin are given before during and for a short time after some medical procedures that require extracorporeal life support ECLS During these procedures the patient s blood is filtered and oxygenated outside of the body using mechanical devices The blood s contact with artificial surfaces activates the clotting process Special cell fragments in the blood called platelets and proteins called coagulation factors are activated in a sequence of steps that results in blood clot formation A high dose of heparin prevents clot from forming during ECLS but results in a delicate balance between clotting and bleeding The ACT is a rapid test that can be performed at a person s bedside prior to surgery or other medical procedures and in or near the operating room at intervals during and immediately after surgery This type of testing is known as point-of-care testing ACT testing allows relatively rapid changes in heparin infusion helping to achieve and maintain a constant level of anticoagulation Once the procedure is complete and the patient has been stabilized heparin doses are typically decreased The ACT measures the inhibiting effect that heparin has on the body s clotting system not the actual level of heparin in the blood The sensitivity of the ACT test to heparin depends on the method used Some ACT tests are designed to monitor lower levels of heparin while others are best at monitoring high levels of heparin When heparin reaches therapeutic maintenance levels the ACT is usually replaced as a monitoring tool by the PTT The ACT test is also sometimes used to monitor regular-dose heparin therapy in people with documented lupus anticoagulant LAC The PTT test cannot be used in those patients because LAC interferes with the PTT In rare clinical situations the ACT test may also be used to monitor the inhibiting effect of a different class of anticoagulation drugs called direct thrombin inhibitors e g argatroban on the clotting system

The ACT is ordered after someone has received an initial dose bolus of heparin and before the start of an open heart surgery or other procedure that requires a high level of anticoagulation During surgery the ACT is measured at intervals to achieve and maintain a steady level of heparin anticoagulation After surgery the ACT is monitored until the person has stabilized and the heparin dosage has been reduced and or neutralized with a counter agent Occasionally the ACT may be measured during a bleeding episode or used as part of a bedside evaluation of a person s heparin anticoagulation level particularly if the person has lupus anticoagulant It may also be used when someone is receiving direct thrombin inhibitor therapy

The ACT is measured in seconds the longer the time to clot the higher the degree of clotting inhibition During surgery the ACT is kept above a lower time limit a limit at which most people will not form blood clots There is no widespread agreement of exactly what this lower limit should be It will vary from hospital to hospital and depends to some degree on the method used to determine ACT It is important to evaluate how the person is responding to this ACT lower limit and to the amount of heparin that person is being given The amount of heparin needed to reach and maintain a certain ACT for instance 300 seconds will vary as will the body s clotting potential at that ACT If there are clotting or bleeding problems the dosages and ACT may need to be adjusted accordingly After surgery the ACT may be maintained within a narrow range for instance 175 - 225 seconds until the person has stabilized

ACT and PTT results are not interchangeable In the area where they overlap upper measurements of PTT and lower levels of ACT they have poor correlation ACT and PTT results should be evaluated independently It is better to determine someone s heparin anticoagulant requirements stabilize the person and then change the monitoring tool The ACT may be influenced by a person s platelet count and platelet function Platelets that are activated during surgery often become dysfunctional and both surgery and heparin can sometimes cause platelet numbers to decrease thrombocytopenia The temperature of the blood may also affect ACT results the blood tends to cool during surgery as it is mechanically filtered and oxygenated Acquired and inherited conditions such as coagulation factor deficiencies may also affect ACT results

Rarely is the test performed in the central laboratory The sample is not stable and the result is needed rapidly to guide treatment So the test must be performed immediately close to the patient usually at the person s bedside in the operating room or in a laboratory close to these locations The ACT is therefore considered a point-of-care test

The ACT test is generally not affected by lupus anticoagulant LAC Nevertheless the presence of LAC has been shown to interfere with certain ACT testing Therefore it is important for the laboratory to follow the manufacturer s instructions and determine if the test is suitable to monitor heparin therapy in a person with documented history of LAC or antiphospholipid syndrome